Burnham HF SERIES Manuel d'instructions

1Price - $3.00INSTALLATION, OPERATING ANDSERVICE INSTRUCTIONS FORHF SERIES OIL FIRED BOILER8143709R3-12/99BEFORE INSTALLATION: READ THIS MANUALSAVE T

10THE FOLLOWING GUIDELINES SHOULD BE FOLLOWEDWHEN PIPING THE TANKLESS HEATER:1. FLOW REGULATION — If flow through the heateris greater than its rating

11Figure 6: Recommended Smokepipe Arrangement and Chimney RequirementsFigure 7: Proper and Improper Locations of Draft Regulator

12Figure 8: Recommended Boiler Piping for Circulator Zoned Heating Systems

13Figure 9: Boiler Piping for Zone Valve Zoned Heating Systems

14H. Electrical1. Install wiring and electrically ground boiler inaccordance with requirements of the authorityhaving jurisdiction, or in absence of s

15Figure 10: Wiring Diagram for Water Boilers with Beckett AFG Burner and Controls, without Tankless HeaterFigure 11: Wiring Diagram for Water Boilers

16J. Oil Piping1. Use flexible oil line(s) so that burner can beremoved without disconnecting the oil supply.2. A supply line fuel oil filter is recom

17L. Two-Pipe Oil Lines1. For two-piped systems, where more lift is required,the two-stage fuel unit is recommended. Table 2(single-stage) and Table

18III. System Start-UpA. Verify that the venting, water piping, oil piping, andelectrical system are installed properly. Refer toinstallation instru

19SOLID stream without air bubbles for approxi-mately 10 seconds.3. Close vent fitting and burner flame should startimmediately.4. If the burner does

2The following terms are used throughout this manual to bring attention to the presence of hazards of various risk levels,or to important information

20delicate and should protected from dirt andabuse. Nozzles are mass produced and can varyfrom sample to sample. For all of those reasonsa spare noz

21i. Fitting leaks due to misflared tubing ordamaged fitting.ii. Fuel line leak due to crushed or bent tubing.iii. Filter connection leaks.iv. Tank co

22• Push red reset button to reset safety switch.b. Simulate ignition failure:• Follow the starting procedure to turn on theburner, but do not open th

23IV. Service and CleaningA. General. Inspection, service and cleaning should beconducted annually. Turn off electric power and closeoil supply val

24NOTE: When ordering parts always give the serial number and model number shown on the boiler. Also provide the name of the part(s) shown below:Figu

25ITEM NO. DESCRIPTION PART NUMBER1Rear Smoke box61137004 611470052Jacket - Lower Rear70437033 704370423Shell8103701 81037024Jacket - Right Side Panel

26Figure 16: Beckett AFG Oil Burner Repair PartFor replacement oil burner parts, contact your wholesaler or the burner manufacturer: R.W. Beckett Co

27BECKETT BURNER PARTS LIST FOR RSA SERIES STEEL BOILERSFOR REPLACEMENT OIL BURNER PARTS, CONTACT YOUR WHOLESALER OR THE BURNERMANUFACTURER:R. W. BECK

28

3DANGERDO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this or anyother appliance.WARNINGImproper installation, a

4Tables of ContentsI. General Information ... 5II. Installation Instructions ... 8III. System Start-Up

5 I: General InformationFigure 1: HF Packaged Boiler (HF-98/HF-173)Notes:1.2.3.4.5.Firing rates based on 140,000 BTU per gallon of oilIBR net water

6A. INSPECT SHIPMENT carefully for any signs of damage.1. ALL EQUIPMENT is carefully manufactured,inspected and packed. Our responsibility ceasesupon

7C. PROVIDE AIR SUPPLY AND VENTILATION toaccommodate proper combustion. If natural ventilationis inadequate, provide a screened opening or duct fromt

8II. Installation Instructions A. Design a piping system and install boiler which willprevent oxygen contamination of boiler water andfrequent water

9Figure 3: Recommended Piping for CombinationHeating and Cooling (Refrigeration) SystemB. Install Pressure Relief Valve. See Figures 8 and 9.Pressur